The surface of the iron will inevitably get dirty with use. Even the most expensive equipment with ultra-fashionable coating is not insured against this. And you are unlikely to be able to avoid adversity, but this is not a reason to panic and get upset! We will tell you 8 ways how to independently clean the iron from burns at home and not spoil the equipment!
1. Vinegar
This is the simplest and most time-tested method for fresh and old burn-in. Don't worry about the smell - just ventilate the room well enough for it to go away.
You will need:
A few tablespoons of vinegar and rock salt.
What to do:
In a metal bowl or saucepan, mix the vinegar and salt in half, put on a small fire and wait until the salt dissolves. Make sure that the vinegar does not boil. Cool the mass and wipe the surface of the iron with a soft cloth or sponge. If any stains remain, hold the mixture on them for literally a couple of minutes and wipe with a soft brush. Remove the remaining solution with a napkin and iron the unnecessary rags with a heated iron several times before use.
2. Soda
This is a very easy and gentle way to clean your iron and is suitable for light dirt. The main thing is not to use metal sponges or other harsh abrasives, so as not to scratch the coating.
You will need:
A few spoons of water and baking soda.
What to do:
Combine the water and baking soda to form a thick paste and spread it over the soleplate with a cloth, then gently wipe it off. You do not need to heat the iron - everything will go away from the cold one too. The burn will dissolve almost instantly, and the stains can be removed with a regular damp sponge.
How to get rid of bedbugs at home
3. Salt
If you have, take sea salt - it absorbs any dirt faster. And at the same time it is an excellent natural antiseptic - you will also get disinfection. Just take salt without dyes, flavors and additives.
You will need:
A thick sheet of paper and a spoonful of salt.
What to do:
Drain all the water from the iron, turn off the steam and heat it at maximum power. Spread a spoonful of coarse salt in an even layer on an old pillowcase or thick paper sheet. Iron it back and forth several times - and the burn will go away by itself. The main thing is not to press too hard so as not to scratch the surface of the sole on the salt crystals.
4. Toothpaste
Toothpaste is a fairly effective, but at the same time, delicate cleaning agent for the iron. As in the case of salt, the simplest and most budgetary one without additives, dyes and flavors is better suited.
You will need:
A drop of toothpaste.
What to do:
Just a little paste is enough for you - you need to apply it on the sole of the iron with a thin layer. Rub the dirtiest places a little separately and leave everything for 5-10 minutes, while the paste will eat away burns and plaque. Wipe the surface and iron a waste cloth a couple of times for final cleaning.
We clean gold at home: 10 ways
5. Peroxide
You can remove any stains, streaks and plaque with ordinary pharmacy peroxide. It is a universal cleaning agent for different types of dirt, so it is useful not only for the iron.
You will need:
A vial of hydrogen peroxide.
What to do:
Soak a rag or cotton pad in it and gently three surfaces of the iron soleplate. This method works well with any others: for example, with salt or soda. If some areas are not cleaned immediately, after such treatment it will be much easier to wash them.
6. Paraffin
This is not the easiest, but a delicate and very effective method for cleaning any irons. Prepare for the molten paraffin to flow, so it's best to put some unnecessary tray or plank down.
You will need:
Paraffin candle and cotton cloth.
What to do:
You need to wrap the candle in an old pillowcase or any piece of cotton cloth and gently wipe the sole of the iron.The main thing is to wrap the candle so that the paraffin does not get to the surface. It is difficult to clean it if it clogs in the holes, so you will get dirty things for a long time when ironing.
Types of blue cheeses: names, photos and descriptions
7. Acetone
Try not to spill acetone on the plastic parts of the iron, so as not to spoil anything - it is still too aggressive. Don't worry about the outsole - nothing will happen to this coating.
You will need:
Nail polish remover.
What to do:
You can remove strong burns, adhered polyethylene or synthetics with acetone. Nail polish remover and a regular cotton pad will work - just three stains until it's gone. If you have an acetone-free wash, it works too, because the principle is the same.
8. How can I avoid burning on the iron?
The main thing is to always set the right temperature for different types of fabric, and not the smoothness of sweaters and underwear on the same mode. After use, wipe the soleplate of the iron with a soft cloth so that plaque does not accumulate or dry out. Delicate items that are sensitive to temperatures (wool, synthetics) smooth through the backing. Otherwise, you can ruin both the clothes and the iron at the same time, and you definitely don't need it!
