The purest water flows from the tap, you have filters on filters at home, and you treat all things as if they were made of silk - and even this is not a panacea for blockages, scale and mold in the washing machine. So do not forget to periodically clean it, so that later you do not have to urgently look for a master. We will tell you 8 effective ways how!
1. How to descale my washing machine?
You probably had to descale the kettle with citric acid, right? The same principle comes in handy with a washing machine - the heating elements are essentially the same. Pour 100 g of acid into the powder compartment and set the longest setting to 90 degrees.
During washing, watch for sounds: if there is too much scale, it falls off in pieces and sometimes clogs the drain. You will understand that this has happened if the car starts humming and rattling. Then you need to turn it off, remove a piece of scale by hand, and continue washing further.
When you're done, check that there are no lumps of scale left in the drum. Be sure to look under the seal and in it, check the drain again - and you can finally rest. Such preventive cleaning is recommended to be done every 5-6 months.
2. How to clean the machine from dirt?
Use a bag of baking soda and a soft cloth or sponge to clean the dirt from the washing machine drum. Pour it directly onto a rag and flush out the reservoir by hand until dirt and plaque begins to loosen. Without rinsing, leave the machine to stand for about half an hour, and rub it vigorously with baking soda again. Then run an express wash at a high temperature.
How to clean a silver chain at home: 10 effective ways
3. How to clean the washing machine from mold?
Mold does not like acids, alkalis and high temperatures, so the methods will be appropriate. Take half a glass of vinegar, but in this case, pause in the middle of the wash, wait 1-2 hours, and only then finish. Use a 1: 2 vinegar solution to treat all exposed and accessible surfaces of the washing machine.
Home gardeners will surely have copper sulfate powder. If this is about you, make a solution out of it: 50 g in a 5-liter bucket of water. Spray all surfaces and parts of the washer with liquid along with the container, drum and cuffs, wait 3-4 hours, and start rinsing.
Alkaline soda ash can be used in the same way. It copes with dirt better and faster than the usual food. The main thing then is to wipe it thoroughly from all nodes and joints with a damp sponge.
4. How to get rid of the smell in the washing machine?
If there are no obvious traces of mold or other problems, but an unpleasant odor is clearly felt, pour a few bags of citric acid (100-150 g) into the powder compartment. Select the longest cycle at the highest temperature and run a dry wash.
How do I clean my carpet at home?
5. Cleaning the drain filter
The drain filter catches debris, large fluff, threads, buttons, buttons and other little things so that the sewage system does not get clogged. That is why it must be cleaned regularly every few months. Otherwise, the contents begin to grow moldy, rot, stink, or it may completely clog the drain.
6. We clean the cuff of the washing machine
The cuff is a seal on the drum door, in the folds of which detergents, dirt, fine debris accumulate. This is where mold and mildew appear most often, so don't forget to clean it out too. To do this, carefully remove the seal with a screwdriver, running in a circle so as not to spoil the rubber.
Wipe the cuff with a cloth and soak it briefly in a bowl of detergent or bleach. During this time, you can just wash the doors and drum. Rinse the seal with running water, wait until everything is dry and put it back in place.
How to clean the iron from burns at home?
7. How do I clean the drain hose?
Over time, dirt and deposits accumulate on the inner walls of the drain hose. If the car smells unpleasant, but you can't find the reason, look into it. To clean the hose, run a short wash at the maximum temperature. If this does not help, it is easier to replace it with a new one, because in fact it is a consumable.
8. How do I clean the powder compartment?
Although it is in the tray that all the detergents are poured, this does not prevent it from being the dirtiest compartment of the machine. And all because a little water constantly remains in it - and this is a favorable environment for fungus and bacteria. In most machines, to remove the tray, you need to press the special tab in the rinse aid compartment.
Wash the plaque compartment with running water and soak it for several hours in water and detergent. Then scrub with a brush and go over all corners and joints with cotton swabs. Rinse again with clean water and air dry.
When you take out the compartment, use a flashlight to illuminate the channels for supplying detergents. If you notice any dirt or mold, clean them with a small, thin brush. Usually, the channels are clogged just because of the dirty tray, and not vice versa, so it is better to keep an eye on it in time.
